CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

ca plante sur batterie

27 oct. 2013, 21:45

Bonjour
Sur asus eeepc 1225b, sur batterie, xubuntu se fige au bout de quelques minutes.....

Vous avez un solution ???
J'aime bien comprendre...

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

27 oct. 2013, 21:53

Bon ben même sur secteur.
Impossible de faire mes mises a jour, j en ai marre

Help please
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

28 oct. 2013, 11:40

Hello cisco, un petit coup d’œil ICI peut être.
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

28 oct. 2013, 23:15

Merci pingux mais je pense vraiment que mon problème est très particulier...je ne trouve rien de semblable sur le web.
J'aime bien comprendre...

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

28 oct. 2013, 23:18

Je suis persuadé qu il y a un rapport avec le wifi. Sais tu quel fichier log peut me donner les infos qui se sont passées avant plantage??
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

29 oct. 2013, 01:11

Dans un terminal tu tapes cette commande : dmesg bonne lecture. ;)
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

29 oct. 2013, 09:10

Merci PINGUX, ca donne ça mais ça ressemble surtout a un démarrage d ordi non? n y a t il pas un fichier journal qui note tout sur plusieurs jours? peut on en créer un?

Merci encore

voila dmesg:

[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 3, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0xffffffff base: 0xfed00000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009d000 - 000000000009e000
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 000000006ec5e000 - 000000006eca1000
[ 0.000000] PM: Registered nosave memory: 000000006eca1000 - 000000006ecb3000
[ 0.000000] PM: Registered nosave memory: 000000006ecb3000 - 000000006ecb6000
[ 0.000000] PM: Registered nosave memory: 000000006ecb6000 - 000000006ecb9000
[ 0.000000] PM: Registered nosave memory: 000000006ecb9000 - 000000006ecc1000
[ 0.000000] PM: Registered nosave memory: 000000006ecc1000 - 000000006ecdb000
[ 0.000000] PM: Registered nosave memory: 000000006ecdc000 - 000000006ecec000
[ 0.000000] PM: Registered nosave memory: 000000006ecec000 - 000000006ecf6000
[ 0.000000] PM: Registered nosave memory: 000000006ed04000 - 000000006ed06000
[ 0.000000] PM: Registered nosave memory: 000000006ed06000 - 000000006ed08000
[ 0.000000] PM: Registered nosave memory: 000000006ed08000 - 000000006ed10000
[ 0.000000] PM: Registered nosave memory: 000000006ed10000 - 000000006ed45000
[ 0.000000] PM: Registered nosave memory: 000000006ed45000 - 000000006ed88000
[ 0.000000] e820: [mem 0x6ef00000-0xfebfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:2 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88006ea00000 s83584 r8192 d22912 u1048576
[ 0.000000] pcpu-alloc: s83584 r8192 d22912 u1048576 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 446896
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-42-generic root=UUID=3bc10ab6-fa02-48a8-99b1-8372a3638af8 ro quiet splash i8042.reset i8042.nomux vt.handoff=7
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 1756240k/1817600k available (6718k kernel code, 1592k absent, 59768k reserved, 6450k data, 932k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16640 nr_irqs:512 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] vt handoff: transparent VT on vt#7
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 7340032 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.004000] Detected 997.947 MHz processor.
[ 0.000007] Calibrating delay loop (skipped), value calculated using timer frequency.. 1995.89 BogoMIPS (lpj=3991788)
[ 0.000016] pid_max: default: 32768 minimum: 301
[ 0.000076] Security Framework initialized
[ 0.000111] AppArmor: AppArmor initialized
[ 0.000116] Yama: becoming mindful.
[ 0.000625] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.002258] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.003107] Mount-cache hash table entries: 256
[ 0.003635] Initializing cgroup subsys cpuacct
[ 0.003645] Initializing cgroup subsys memory
[ 0.003669] Initializing cgroup subsys devices
[ 0.003674] Initializing cgroup subsys freezer
[ 0.003679] Initializing cgroup subsys blkio
[ 0.003683] Initializing cgroup subsys perf_event
[ 0.003752] tseg: 006ef00000
[ 0.003758] CPU: Physical Processor ID: 0
[ 0.003762] CPU: Processor Core ID: 0
[ 0.003766] mce: CPU supports 6 MCE banks
[ 0.009315] ACPI: Core revision 20120320
[ 0.032447] ftrace: allocating 25123 entries in 99 pages
[ 0.067255] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.106950] CPU0: AMD C-60 APU with Radeon(tm) HD Graphics stepping 00
[ 0.214661] Performance Events: AMD PMU driver.
[ 0.214673] ... version: 0
[ 0.214678] ... bit width: 48
[ 0.214682] ... generic registers: 4
[ 0.214687] ... value mask: 0000ffffffffffff
[ 0.214691] ... max period: 00007fffffffffff
[ 0.214696] ... fixed-purpose events: 0
[ 0.214700] ... event mask: 000000000000000f
[ 0.215142] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.215412] Booting Node 0, Processors #1 Ok.
[ 0.228531] TSC synchronization [CPU#0 -> CPU#1]:
[ 0.228538] Measured 128046800 cycles TSC warp between CPUs, turning off TSC clock.
[ 0.008000] Marking TSC unstable due to check_tsc_sync_source failed
[ 0.116133] Brought up 2 CPUs
[ 0.116142] Total of 2 processors activated (3991.78 BogoMIPS).
[ 0.116848] devtmpfs: initialized
[ 0.121964] EVM: security.selinux
[ 0.121971] EVM: security.SMACK64
[ 0.121976] EVM: security.capability
[ 0.124140] PM: Registering ACPI NVS region [mem 0x6ec5e000-0x6eca0fff] (274432 bytes)
[ 0.124182] PM: Registering ACPI NVS region [mem 0x6ecb3000-0x6ecb5fff] (12288 bytes)
[ 0.124189] PM: Registering ACPI NVS region [mem 0x6ecb9000-0x6ecc0fff] (32768 bytes)
[ 0.124197] PM: Registering ACPI NVS region [mem 0x6ecec000-0x6ecf5fff] (40960 bytes)
[ 0.124204] PM: Registering ACPI NVS region [mem 0x6ed04000-0x6ed05fff] (8192 bytes)
[ 0.124211] PM: Registering ACPI NVS region [mem 0x6ed08000-0x6ed0ffff] (32768 bytes)
[ 0.124218] PM: Registering ACPI NVS region [mem 0x6ed45000-0x6ed87fff] (274432 bytes)
[ 0.126685] dummy:
[ 0.126788] RTC time: 8:56:25, date: 10/29/13
[ 0.126913] NET: Registered protocol family 16
[ 0.127099] Trying to unpack rootfs image as initramfs...
[ 0.127792] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.127803] ACPI: bus type pci registered
[ 0.128060] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.128071] PCI: not using MMCONFIG
[ 0.128076] PCI: Using configuration type 1 for base access
[ 0.128081] PCI: Using configuration type 1 for extended access
[ 0.131623] bio: create slab <bio-0> at 0
[ 0.131965] ACPI: Added _OSI(Module Device)
[ 0.131974] ACPI: Added _OSI(Processor Device)
[ 0.131981] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.131988] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.137581] ACPI: EC: EC description table is found, configuring boot EC
[ 0.137598] ACPI: EC: Look up EC in DSDT
[ 0.144558] ACPI: Executed 3 blocks of module-level executable AML code
[ 0.152599] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.216938] ACPI: Interpreter enabled
[ 0.216961] ACPI: (supports S0 S3 S4 S5)
[ 0.217028] ACPI: Using IOAPIC for interrupt routing
[ 0.220429] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.220590] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.357261] ACPI: EC: GPE = 0xc, I/O: command/status = 0x66, data = 0x62
[ 0.357923] ACPI: No dock devices found.
[ 0.357939] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.358529] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.359357] pci_root PNP0A08:00: host bridge window [io 0x0000-0x03af]
[ 0.359368] pci_root PNP0A08:00: host bridge window [io 0x03e0-0x0cf7]
[ 0.359376] pci_root PNP0A08:00: host bridge window [io 0x03b0-0x03df]
[ 0.359385] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.359394] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.359402] pci_root PNP0A08:00: host bridge window [mem 0x000c0000-0x000dffff]
[ 0.359410] pci_root PNP0A08:00: host bridge window [mem 0x7f000000-0xffffffff]
[ 0.359522] PCI host bridge to bus 0000:00
[ 0.359534] pci_bus 0000:00: root bus resource [io 0x0000-0x03af]
[ 0.359542] pci_bus 0000:00: root bus resource [io 0x03e0-0x0cf7]
[ 0.359549] pci_bus 0000:00: root bus resource [io 0x03b0-0x03df]
[ 0.359557] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.359565] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.359573] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
[ 0.359581] pci_bus 0000:00: root bus resource [mem 0x7f000000-0xffffffff]
[ 0.359607] pci 0000:00:00.0: [1022:1510] type 00 class 0x060000
[ 0.359696] pci 0000:00:01.0: [1002:9807] type 00 class 0x030000
[ 0.359721] pci 0000:00:01.0: reg 10: [mem 0xc0000000-0xcfffffff pref]
[ 0.359739] pci 0000:00:01.0: reg 14: [io 0xf000-0xf0ff]
[ 0.359757] pci 0000:00:01.0: reg 18: [mem 0xfeb00000-0xfeb3ffff]
[ 0.359849] pci 0000:00:01.0: supports D1 D2
[ 0.359890] pci 0000:00:01.1: [1002:1314] type 00 class 0x040300
[ 0.359912] pci 0000:00:01.1: reg 10: [mem 0xfeb44000-0xfeb47fff]
[ 0.360045] pci 0000:00:01.1: supports D1 D2
[ 0.360100] pci 0000:00:04.0: [1022:1512] type 01 class 0x060400
[ 0.360219] pci 0000:00:04.0: PME# supported from D0 D3hot D3cold
[ 0.360305] pci 0000:00:11.0: [1002:4391] type 00 class 0x010601
[ 0.360344] pci 0000:00:11.0: reg 10: [io 0xf140-0xf147]
[ 0.360365] pci 0000:00:11.0: reg 14: [io 0xf130-0xf133]
[ 0.360387] pci 0000:00:11.0: reg 18: [io 0xf120-0xf127]
[ 0.360408] pci 0000:00:11.0: reg 1c: [io 0xf110-0xf113]
[ 0.360429] pci 0000:00:11.0: reg 20: [io 0xf100-0xf10f]
[ 0.360450] pci 0000:00:11.0: reg 24: [mem 0xfeb4f000-0xfeb4f3ff]
[ 0.360561] pci 0000:00:12.0: [1002:4397] type 00 class 0x0c0310
[ 0.360590] pci 0000:00:12.0: reg 10: [mem 0xfeb4e000-0xfeb4efff]
[ 0.360719] pci 0000:00:12.2: [1002:4396] type 00 class 0x0c0320
[ 0.360757] pci 0000:00:12.2: reg 10: [mem 0xfeb4d000-0xfeb4d0ff]
[ 0.360898] pci 0000:00:12.2: supports D1 D2
[ 0.360906] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[ 0.360956] pci 0000:00:13.0: [1002:4397] type 00 class 0x0c0310
[ 0.360985] pci 0000:00:13.0: reg 10: [mem 0xfeb4c000-0xfeb4cfff]
[ 0.361114] pci 0000:00:13.2: [1002:4396] type 00 class 0x0c0320
[ 0.361152] pci 0000:00:13.2: reg 10: [mem 0xfeb4b000-0xfeb4b0ff]
[ 0.361294] pci 0000:00:13.2: supports D1 D2
[ 0.361301] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[ 0.361352] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
[ 0.361495] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
[ 0.361538] pci 0000:00:14.2: reg 10: [mem 0xfeb40000-0xfeb43fff 64bit]
[ 0.361653] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[ 0.361690] pci 0000:00:14.3: [1002:439d] type 00 class 0x060100
[ 0.361834] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
[ 0.361918] pci 0000:00:14.5: [1002:4399] type 00 class 0x0c0310
[ 0.361947] pci 0000:00:14.5: reg 10: [mem 0xfeb4a000-0xfeb4afff]
[ 0.362079] pci 0000:00:15.0: [1002:43a0] type 01 class 0x060400
[ 0.362222] pci 0000:00:15.0: supports D1 D2
[ 0.362278] pci 0000:00:15.1: [1002:43a1] type 01 class 0x060400
[ 0.362418] pci 0000:00:15.1: supports D1 D2
[ 0.362476] pci 0000:00:15.3: [1002:43a3] type 01 class 0x060400
[ 0.362617] pci 0000:00:15.3: supports D1 D2
[ 0.362673] pci 0000:00:16.0: [1002:4397] type 00 class 0x0c0310
[ 0.362701] pci 0000:00:16.0: reg 10: [mem 0xfeb49000-0xfeb49fff]
[ 0.362831] pci 0000:00:16.2: [1002:4396] type 00 class 0x0c0320
[ 0.362869] pci 0000:00:16.2: reg 10: [mem 0xfeb48000-0xfeb480ff]
[ 0.363010] pci 0000:00:16.2: supports D1 D2
[ 0.363018] pci 0000:00:16.2: PME# supported from D0 D1 D2 D3hot
[ 0.363072] pci 0000:00:18.0: [1022:1700] type 00 class 0x060000
[ 0.363159] pci 0000:00:18.1: [1022:1701] type 00 class 0x060000
[ 0.363230] pci 0000:00:18.2: [1022:1702] type 00 class 0x060000
[ 0.363305] pci 0000:00:18.3: [1022:1703] type 00 class 0x060000
[ 0.363396] pci 0000:00:18.4: [1022:1704] type 00 class 0x060000
[ 0.363468] pci 0000:00:18.5: [1022:1718] type 00 class 0x060000
[ 0.363540] pci 0000:00:18.6: [1022:1716] type 00 class 0x060000
[ 0.363611] pci 0000:00:18.7: [1022:1719] type 00 class 0x060000
[ 0.363767] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.363923] pci 0000:00:14.4: PCI bridge to [bus 02-02] (subtractive decode)
[ 0.363944] pci 0000:00:14.4: bridge window [io 0x0000-0x03af] (subtractive decode)
[ 0.363952] pci 0000:00:14.4: bridge window [io 0x03e0-0x0cf7] (subtractive decode)
[ 0.363960] pci 0000:00:14.4: bridge window [io 0x03b0-0x03df] (subtractive decode)
[ 0.363968] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.363976] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.363993] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
[ 0.364001] pci 0000:00:14.4: bridge window [mem 0x7f000000-0xffffffff] (subtractive decode)
[ 0.364116] pci 0000:00:15.0: PCI bridge to [bus 03-03]
[ 0.364261] pci 0000:04:00.0: [168c:0032] type 00 class 0x028000
[ 0.364308] pci 0000:04:00.0: reg 10: [mem 0xfea00000-0xfea7ffff 64bit]
[ 0.364399] pci 0000:04:00.0: reg 30: [mem 0xfea80000-0xfea8ffff pref]
[ 0.364502] pci 0000:04:00.0: supports D1 D2
[ 0.364510] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.372101] pci 0000:00:15.1: PCI bridge to [bus 04-04]
[ 0.372132] pci 0000:00:15.1: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.372305] pci 0000:05:00.0: [10ec:8136] type 00 class 0x020000
[ 0.372348] pci 0000:05:00.0: reg 10: [io 0xe000-0xe0ff]
[ 0.372401] pci 0000:05:00.0: reg 18: [mem 0xd0004000-0xd0004fff 64bit pref]
[ 0.372440] pci 0000:05:00.0: reg 20: [mem 0xd0000000-0xd0003fff 64bit pref]
[ 0.372576] pci 0000:05:00.0: supports D1 D2
[ 0.372584] pci 0000:05:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.380120] pci 0000:00:15.3: PCI bridge to [bus 05-05]
[ 0.380148] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.380169] pci 0000:00:15.3: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.380232] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.380660] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT]
[ 0.380863] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE20._PRT]
[ 0.380978] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE21._PRT]
[ 0.381118] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE23._PRT]
[ 0.381303] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.381316] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 0.381321] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.489302] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 7 10 11 14 15) *0
[ 0.489571] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 10 11 14 15) *0
[ 0.489870] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 11 14 15) *0
[ 0.490132] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 10 11 14 15) *0
[ 0.490392] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 14 15) *0
[ 0.490579] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 14 15) *0
[ 0.490805] ACPI: PCI Interrupt Link [LNKG] (IRQs 4 7 10 11 14 15) *0
[ 0.491009] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 14 15) *0
[ 0.491329] vgaarb: device added: PCI:0000:00:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.491374] vgaarb: loaded
[ 0.491380] vgaarb: bridge control possible 0000:00:01.0
[ 0.491962] SCSI subsystem initialized
[ 0.492188] libata version 3.00 loaded.
[ 0.492267] ACPI: bus type usb registered
[ 0.492331] usbcore: registered new interface driver usbfs
[ 0.492364] usbcore: registered new interface driver hub
[ 0.492467] usbcore: registered new device driver usb
[ 0.492758] PCI: Using ACPI for IRQ routing
[ 0.505445] PCI: pci_cache_line_size set to 64 bytes
[ 0.505676] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.505683] e820: reserve RAM buffer [mem 0x6ec5e000-0x6fffffff]
[ 0.505691] e820: reserve RAM buffer [mem 0x6ecdc000-0x6fffffff]
[ 0.505698] e820: reserve RAM buffer [mem 0x6ed04000-0x6fffffff]
[ 0.505705] e820: reserve RAM buffer [mem 0x6ef00000-0x6fffffff]
[ 0.506003] NetLabel: Initializing
[ 0.506010] NetLabel: domain hash size = 128
[ 0.506015] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.506049] NetLabel: unlabeled traffic allowed by default
[ 0.506261] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.506277] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[ 0.508094] Switching to clocksource hpet
[ 0.536124] AppArmor: AppArmor Filesystem Enabled
[ 0.536211] pnp: PnP ACPI init
[ 0.536261] ACPI: bus type pnp registered
[ 0.536813] pnp 00:00: [bus 00-ff]
[ 0.536826] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.536835] pnp 00:00: [io 0x0000-0x03af window]
[ 0.536843] pnp 00:00: [io 0x03e0-0x0cf7 window]
[ 0.536852] pnp 00:00: [io 0x03b0-0x03df window]
[ 0.536860] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.536869] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.536877] pnp 00:00: [mem 0x000c0000-0x000dffff window]
[ 0.536885] pnp 00:00: [mem 0x7f000000-0xffffffff window]
[ 0.536892] pnp 00:00: [mem 0x00000000 window]
[ 0.537081] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.537222] pnp 00:01: [mem 0xe0000000-0xefffffff]
[ 0.537380] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.537395] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.539328] pnp 00:02: [io 0x040b]
[ 0.539338] pnp 00:02: [io 0x04d6]
[ 0.539345] pnp 00:02: [io 0x0c00-0x0c01]
[ 0.539352] pnp 00:02: [io 0x0c14]
[ 0.539359] pnp 00:02: [io 0x0c50-0x0c51]
[ 0.539374] pnp 00:02: [io 0x0c52]
[ 0.539381] pnp 00:02: [io 0x0c6c]
[ 0.539388] pnp 00:02: [io 0x0c6f]
[ 0.539395] pnp 00:02: [io 0x0cd0-0x0cd1]
[ 0.539402] pnp 00:02: [io 0x0cd2-0x0cd3]
[ 0.539409] pnp 00:02: [io 0x0cd4-0x0cd5]
[ 0.539416] pnp 00:02: [io 0x0cd6-0x0cd7]
[ 0.539422] pnp 00:02: [io 0x0cd8-0x0cdf]
[ 0.539429] pnp 00:02: [io 0x0800-0x089f]
[ 0.539437] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled]
[ 0.539445] pnp 00:02: [io 0x0000-0x000f]
[ 0.539452] pnp 00:02: [io 0x0b20-0x0b3f]
[ 0.539458] pnp 00:02: [io 0x0900-0x090f]
[ 0.539465] pnp 00:02: [io 0x0910-0x091f]
[ 0.539473] pnp 00:02: [io 0xfe00-0xfefe]
[ 0.539480] pnp 00:02: [io 0x0060-0x005f disabled]
[ 0.539487] pnp 00:02: [io 0x0064-0x0063 disabled]
[ 0.539495] pnp 00:02: [mem 0xfec00000-0xfec00fff]
[ 0.539502] pnp 00:02: [mem 0xfee00000-0xfee00fff]
[ 0.539509] pnp 00:02: [mem 0xfed80000-0xfed8ffff]
[ 0.539517] pnp 00:02: [mem 0xfed61000-0xfed70fff]
[ 0.539524] pnp 00:02: [mem 0xfec10000-0xfec10fff]
[ 0.539531] pnp 00:02: [mem 0xfed00000-0xfed00fff]
[ 0.539538] pnp 00:02: [mem 0xffe00000-0xffffffff]
[ 0.539724] system 00:02: [io 0x040b] has been reserved
[ 0.539734] system 00:02: [io 0x04d6] has been reserved
[ 0.539743] system 00:02: [io 0x0c00-0x0c01] has been reserved
[ 0.539752] system 00:02: [io 0x0c14] has been reserved
[ 0.539760] system 00:02: [io 0x0c50-0x0c51] has been reserved
[ 0.539769] system 00:02: [io 0x0c52] has been reserved
[ 0.539777] system 00:02: [io 0x0c6c] has been reserved
[ 0.539785] system 00:02: [io 0x0c6f] has been reserved
[ 0.539793] system 00:02: [io 0x0cd0-0x0cd1] has been reserved
[ 0.539802] system 00:02: [io 0x0cd2-0x0cd3] has been reserved
[ 0.539810] system 00:02: [io 0x0cd4-0x0cd5] has been reserved
[ 0.539818] system 00:02: [io 0x0cd6-0x0cd7] has been reserved
[ 0.539827] system 00:02: [io 0x0cd8-0x0cdf] has been reserved
[ 0.539835] system 00:02: [io 0x0800-0x089f] has been reserved
[ 0.539844] system 00:02: [io 0x0b20-0x0b3f] has been reserved
[ 0.539852] system 00:02: [io 0x0900-0x090f] has been reserved
[ 0.539861] system 00:02: [io 0x0910-0x091f] has been reserved
[ 0.539870] system 00:02: [io 0xfe00-0xfefe] has been reserved
[ 0.539882] system 00:02: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.539892] system 00:02: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.539902] system 00:02: [mem 0xfed80000-0xfed8ffff] has been reserved
[ 0.539911] system 00:02: [mem 0xfed61000-0xfed70fff] has been reserved
[ 0.539921] system 00:02: [mem 0xfec10000-0xfec10fff] has been reserved
[ 0.539930] system 00:02: [mem 0xfed00000-0xfed00fff] has been reserved
[ 0.539940] system 00:02: [mem 0xffe00000-0xffffffff] has been reserved
[ 0.539953] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.540000] pnp 00:03: [dma 4]
[ 0.540054] pnp 00:03: [io 0x0000-0x000f]
[ 0.540062] pnp 00:03: [io 0x0081-0x0083]
[ 0.540069] pnp 00:03: [io 0x0087]
[ 0.540076] pnp 00:03: [io 0x0089-0x008b]
[ 0.540083] pnp 00:03: [io 0x008f]
[ 0.540090] pnp 00:03: [io 0x00c0-0x00df]
[ 0.540176] pnp 00:03: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.540218] pnp 00:04: [io 0x0070-0x0071]
[ 0.540269] pnp 00:04: [irq 8]
[ 0.540350] pnp 00:04: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.540384] pnp 00:05: [io 0x0061]
[ 0.540455] pnp 00:05: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.540559] pnp 00:06: [io 0x0010-0x001f]
[ 0.540568] pnp 00:06: [io 0x0022-0x003f]
[ 0.540575] pnp 00:06: [io 0x0044-0x005f]
[ 0.540582] pnp 00:06: [io 0x0072-0x007f]
[ 0.540589] pnp 00:06: [io 0x0080]
[ 0.540595] pnp 00:06: [io 0x0084-0x0086]
[ 0.540602] pnp 00:06: [io 0x0088]
[ 0.540609] pnp 00:06: [io 0x008c-0x008e]
[ 0.540623] pnp 00:06: [io 0x0090-0x009f]
[ 0.540630] pnp 00:06: [io 0x00a2-0x00bf]
[ 0.540637] pnp 00:06: [io 0x00e0-0x00ef]
[ 0.540645] pnp 00:06: [io 0x04d0-0x04d1]
[ 0.540794] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.540808] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.540843] pnp 00:07: [io 0x00f0-0x00ff]
[ 0.540901] pnp 00:07: [irq 13]
[ 0.540974] pnp 00:07: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.541155] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.541214] pnp 00:09: [io 0x0240-0x0259]
[ 0.541348] system 00:09: [io 0x0240-0x0259] has been reserved
[ 0.541361] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.541577] pnp 00:0a: [irq 12]
[ 0.541660] pnp 00:0a: Plug and Play ACPI device, IDs SYN1d15 SYN1d00 SYN0002 PNP0f13 (active)
[ 0.541765] pnp 00:0b: [io 0x0060]
[ 0.541774] pnp 00:0b: [io 0x0064]
[ 0.541829] pnp 00:0b: [irq 1]
[ 0.541917] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.542138] pnp 00:0c: [mem 0x6f000000-0x7effffff]
[ 0.542279] system 00:0c: [mem 0x6f000000-0x7effffff] could not be reserved
[ 0.542292] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.544888] pnp 00:0d: [mem 0xfed00000-0xfed003ff]
[ 0.545123] pnp 00:0d: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.545154] pnp: PnP ACPI: found 14 devices
[ 0.545160] ACPI: ACPI bus type pnp unregistered
[ 0.556132] pci 0000:00:04.0: bridge window [io 0x1000-0x0fff] to [bus 01-01] add_size 1000
[ 0.556150] pci 0000:00:04.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01-01] add_size 200000
[ 0.556162] pci 0000:00:04.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01-01] add_size 200000
[ 0.556227] pci 0000:00:04.0: res[14]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 0.556237] pci 0000:00:04.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.556246] pci 0000:00:04.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.556263] pci 0000:00:04.0: BAR 14: assigned [mem 0x7f000000-0x7f1fffff]
[ 0.556276] pci 0000:00:04.0: BAR 15: assigned [mem 0x7f200000-0x7f3fffff 64bit pref]
[ 0.556290] pci 0000:00:04.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.556301] pci 0000:00:04.0: PCI bridge to [bus 01-01]
[ 0.556312] pci 0000:00:04.0: bridge window [io 0x1000-0x1fff]
[ 0.556324] pci 0000:00:04.0: bridge window [mem 0x7f000000-0x7f1fffff]
[ 0.556335] pci 0000:00:04.0: bridge window [mem 0x7f200000-0x7f3fffff 64bit pref]
[ 0.556349] pci 0000:00:14.4: PCI bridge to [bus 02-02]
[ 0.556373] pci 0000:00:15.0: PCI bridge to [bus 03-03]
[ 0.556397] pci 0000:00:15.1: PCI bridge to [bus 04-04]
[ 0.556410] pci 0000:00:15.1: bridge window [mem 0xfea00000-0xfeafffff]
[ 0.556428] pci 0000:00:15.3: PCI bridge to [bus 05-05]
[ 0.556437] pci 0000:00:15.3: bridge window [io 0xe000-0xefff]
[ 0.556453] pci 0000:00:15.3: bridge window [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.556584] pci_bus 0000:00: resource 4 [io 0x0000-0x03af]
[ 0.556594] pci_bus 0000:00: resource 5 [io 0x03e0-0x0cf7]
[ 0.556602] pci_bus 0000:00: resource 6 [io 0x03b0-0x03df]
[ 0.556610] pci_bus 0000:00: resource 7 [io 0x0d00-0xffff]
[ 0.556618] pci_bus 0000:00: resource 8 [mem 0x000a0000-0x000bffff]
[ 0.556626] pci_bus 0000:00: resource 9 [mem 0x000c0000-0x000dffff]
[ 0.556634] pci_bus 0000:00: resource 10 [mem 0x7f000000-0xffffffff]
[ 0.556643] pci_bus 0000:01: resource 0 [io 0x1000-0x1fff]
[ 0.556650] pci_bus 0000:01: resource 1 [mem 0x7f000000-0x7f1fffff]
[ 0.556659] pci_bus 0000:01: resource 2 [mem 0x7f200000-0x7f3fffff 64bit pref]
[ 0.556667] pci_bus 0000:02: resource 4 [io 0x0000-0x03af]
[ 0.556675] pci_bus 0000:02: resource 5 [io 0x03e0-0x0cf7]
[ 0.556683] pci_bus 0000:02: resource 6 [io 0x03b0-0x03df]
[ 0.556690] pci_bus 0000:02: resource 7 [io 0x0d00-0xffff]
[ 0.556698] pci_bus 0000:02: resource 8 [mem 0x000a0000-0x000bffff]
[ 0.556706] pci_bus 0000:02: resource 9 [mem 0x000c0000-0x000dffff]
[ 0.556714] pci_bus 0000:02: resource 10 [mem 0x7f000000-0xffffffff]
[ 0.556723] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.556731] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.556740] pci_bus 0000:05: resource 2 [mem 0xd0000000-0xd00fffff 64bit pref]
[ 0.556853] NET: Registered protocol family 2
[ 0.557118] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.558658] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.562167] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.562995] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.563003] TCP: reno registered
[ 0.563039] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.563086] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.563307] NET: Registered protocol family 1
[ 0.563357] pci 0000:00:01.0: Boot video device
[ 1.816349] PCI: CLS 64 bytes, default 64
[ 1.817070] LVT offset 0 assigned for vector 0x400
[ 1.817134] perf: AMD IBS detected (0x000000ff)
[ 1.817670] audit: initializing netlink socket (disabled)
[ 1.817702] type=2000 audit(1383036986.816:1): initialized
[ 1.873282] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.878669] VFS: Disk quotas dquot_6.5.2
[ 1.878827] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.880625] fuse init (API version 7.19)
[ 1.880890] msgmni has been set to 3430
[ 1.882404] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.882549] io scheduler noop registered
[ 1.882557] io scheduler deadline registered (default)
[ 1.882663] io scheduler cfq registered
[ 1.883404] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.883460] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.883957] ACPI: AC Adapter [AC0] (on-line)
[ 1.884252] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
[ 1.888381] ACPI: Lid Switch [LID]
[ 1.888580] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 1.888595] ACPI: Sleep Button [SLPB]
[ 1.888719] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.888729] ACPI: Power Button [PWRF]
[ 1.889004] ACPI: acpi_idle registered with cpuidle
[ 1.895615] Freeing initrd memory: 15020k freed
[ 1.907473] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.907489] ACPI: Thermal Zone [THRM] (32 C)
[ 1.907586] ACPI: Battery Slot [BAT0] (battery present)
[ 1.907700] GHES: HEST is not enabled!
[ 1.908081] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.916799] Linux agpgart interface v0.103
[ 1.926191] brd: module loaded
[ 1.926308] ACPI: Battery Slot [BAT0] (battery present)
[ 1.930216] loop: module loaded
[ 1.931403] Fixed MDIO Bus: probed
[ 1.931553] tun: Universal TUN/TAP device driver, 1.6
[ 1.931560] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.931864] PPP generic driver version 2.4.2
[ 1.932106] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.932266] ehci_hcd 0000:00:12.2: EHCI Host Controller
[ 1.932289] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[ 1.932347] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.932400] QUIRK: Enable AMD PLL fix
[ 1.932465] ehci_hcd 0000:00:12.2: debug port 1
[ 1.932526] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfeb4d000
[ 1.944144] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[ 1.944253] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.944263] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.944272] usb usb1: Product: EHCI Host Controller
[ 1.944280] usb usb1: Manufacturer: Linux 3.5.0-42-generic ehci_hcd
[ 1.944287] usb usb1: SerialNumber: 0000:00:12.2
[ 1.944859] hub 1-0:1.0: USB hub found
[ 1.944882] hub 1-0:1.0: 5 ports detected
[ 1.945262] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 1.945284] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 1.945343] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.945395] ehci_hcd 0000:00:13.2: debug port 1
[ 1.945433] ehci_hcd 0000:00:13.2: irq 17, io mem 0xfeb4b000
[ 1.956283] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[ 1.956353] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.956360] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.956367] usb usb2: Product: EHCI Host Controller
[ 1.956373] usb usb2: Manufacturer: Linux 3.5.0-42-generic ehci_hcd
[ 1.956378] usb usb2: SerialNumber: 0000:00:13.2
[ 1.956951] hub 2-0:1.0: USB hub found
[ 1.956969] hub 2-0:1.0: 5 ports detected
[ 1.957295] ehci_hcd 0000:00:16.2: EHCI Host Controller
[ 1.957312] ehci_hcd 0000:00:16.2: new USB bus registered, assigned bus number 3
[ 1.957328] ehci_hcd 0000:00:16.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[ 1.957371] ehci_hcd 0000:00:16.2: debug port 1
[ 1.957403] ehci_hcd 0000:00:16.2: irq 17, io mem 0xfeb48000
[ 1.968283] ehci_hcd 0000:00:16.2: USB 2.0 started, EHCI 1.00
[ 1.968353] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.968361] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.968368] usb usb3: Product: EHCI Host Controller
[ 1.968374] usb usb3: Manufacturer: Linux 3.5.0-42-generic ehci_hcd
[ 1.968379] usb usb3: SerialNumber: 0000:00:16.2
[ 1.968894] hub 3-0:1.0: USB hub found
[ 1.968914] hub 3-0:1.0: 4 ports detected
[ 1.969167] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.969299] ohci_hcd 0000:00:12.0: OHCI Host Controller
[ 1.969321] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 4
[ 1.969422] ohci_hcd 0000:00:12.0: irq 18, io mem 0xfeb4e000
[ 2.028344] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.028356] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.028363] usb usb4: Product: OHCI Host Controller
[ 2.028370] usb usb4: Manufacturer: Linux 3.5.0-42-generic ohci_hcd
[ 2.028375] usb usb4: SerialNumber: 0000:00:12.0
[ 2.028937] hub 4-0:1.0: USB hub found
[ 2.029001] hub 4-0:1.0: 5 ports detected
[ 2.029285] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 2.029303] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[ 2.029350] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfeb4c000
[ 2.088349] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.088361] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.088368] usb usb5: Product: OHCI Host Controller
[ 2.088374] usb usb5: Manufacturer: Linux 3.5.0-42-generic ohci_hcd
[ 2.088380] usb usb5: SerialNumber: 0000:00:13.0
[ 2.088948] hub 5-0:1.0: USB hub found
[ 2.089007] hub 5-0:1.0: 5 ports detected
[ 2.089288] ohci_hcd 0000:00:14.5: OHCI Host Controller
[ 2.089306] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 6
[ 2.089348] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfeb4a000
[ 2.148391] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.148405] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.148414] usb usb6: Product: OHCI Host Controller
[ 2.148422] usb usb6: Manufacturer: Linux 3.5.0-42-generic ohci_hcd
[ 2.148429] usb usb6: SerialNumber: 0000:00:14.5
[ 2.148959] hub 6-0:1.0: USB hub found
[ 2.149017] hub 6-0:1.0: 2 ports detected
[ 2.149310] ohci_hcd 0000:00:16.0: OHCI Host Controller
[ 2.149328] ohci_hcd 0000:00:16.0: new USB bus registered, assigned bus number 7
[ 2.149369] ohci_hcd 0000:00:16.0: irq 18, io mem 0xfeb49000
[ 2.208311] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.208323] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.208329] usb usb7: Product: OHCI Host Controller
[ 2.208336] usb usb7: Manufacturer: Linux 3.5.0-42-generic ohci_hcd
[ 2.208341] usb usb7: SerialNumber: 0000:00:16.0
[ 2.208862] hub 7-0:1.0: USB hub found
[ 2.208920] hub 7-0:1.0: 4 ports detected
[ 2.209122] uhci_hcd: USB Universal Host Controller Interface driver
[ 2.209343] usbcore: registered new interface driver libusual
[ 2.209435] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 2.211756] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.211776] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.212592] mousedev: PS/2 mouse device common for all mice
[ 2.213827] rtc_cmos 00:04: RTC can wake from S4
[ 2.214170] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 2.214255] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
[ 2.214440] device-mapper: uevent: version 1.0.3
[ 2.214723] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
[ 2.214866] cpuidle: using governor ladder
[ 2.215028] cpuidle: using governor menu
[ 2.215035] EFI Variables Facility v0.08 2004-May-17
[ 2.215923] ashmem: initialized
[ 2.216337] TCP: cubic registered
[ 2.216585] NET: Registered protocol family 10
[ 2.217033] NET: Registered protocol family 17
[ 2.217065] Key type dns_resolver registered
[ 2.217853] PM: Hibernation image not present or could not be loaded.
[ 2.217897] registered taskstats version 1
[ 2.225663] Key type trusted registered
[ 2.228381] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 2.233684] Key type encrypted registered
[ 2.242170] Magic number: 1:941:928
[ 2.242380] rtc_cmos 00:04: setting system clock to 2013-10-29 08:56:27 UTC (1383036987)
[ 2.242602] powernow-k8: Found 1 AMD C-60 APU with Radeon(tm) HD Graphics (2 cpu cores) (version 2.20.00)
[ 2.242653] powernow-k8: Core Performance Boosting: on.
[ 2.242756] powernow-k8: 0 : pstate 0 (1000 MHz)
[ 2.242762] powernow-k8: 1 : pstate 1 (800 MHz)
[ 2.243433] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.243444] EDD information not available.
[ 2.249765] Freeing unused kernel memory: 932k freed
[ 2.250389] Write protecting the kernel read-only data: 12288k
[ 2.266898] Freeing unused kernel memory: 1464k freed
[ 2.280079] Freeing unused kernel memory: 1132k freed
[ 2.341774] udevd[88]: starting version 175
[ 2.368135] usb 1-5: new high-speed USB device number 3 using ehci_hcd
[ 2.495284] ahci 0000:00:11.0: version 3.0
[ 2.495588] ahci 0000:00:11.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 2.495601] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part
[ 2.501428] scsi0 : ahci
[ 2.504262] scsi1 : ahci
[ 2.504496] ata1: SATA max UDMA/133 abar m1024@0xfeb4f000 port 0xfeb4f100 irq 19
[ 2.504507] ata2: SATA max UDMA/133 abar m1024@0xfeb4f000 port 0xfeb4f180 irq 19
[ 2.624845] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.625062] r8169 0000:05:00.0: irq 40 for MSI/MSI-X
[ 2.625529] r8169 0000:05:00.0: eth0: RTL8105e at 0xffffc9000034a000, 10:bf:48:23:21:c6, XID 00a00000 IRQ 40
[ 2.685872] usb 1-5: New USB device found, idVendor=13d3, idProduct=5716
[ 2.685890] usb 1-5: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 2.685899] usb 1-5: Product: USB 2.0 UVC VGA WebCam
[ 2.685908] usb 1-5: Manufacturer: Azurewave
[ 2.685916] usb 1-5: SerialNumber: 0x0001
[ 2.824379] ata2: SATA link down (SStatus 0 SControl 300)
[ 2.996301] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 3.048983] ata1.00: ATA-8: ST9320325AS, 0003SDM1, max UDMA/133
[ 3.048996] ata1.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 3.051737] ata1.00: configured for UDMA/133
[ 3.052424] scsi 0:0:0:0: Direct-Access ATA ST9320325AS 0003 PQ: 0 ANSI: 5
[ 3.052984] sd 0:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[ 3.053155] sd 0:0:0:0: [sda] Write Protect is off
[ 3.053164] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.053254] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 3.053357] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.088078] usb 4-2: new full-speed USB device number 2 using ohci_hcd
[ 3.137169] sda: sda1 sda2 sda3 < sda5 sda6 sda7 > sda4
[ 3.139913] sd 0:0:0:0: [sda] Attached SCSI disk
[ 3.261396] usb 4-2: New USB device found, idVendor=046d, idProduct=c52f
[ 3.261414] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 3.261425] usb 4-2: Product: USB Receiver
[ 3.261434] usb 4-2: Manufacturer: Logitech
[ 3.297629] usbcore: registered new interface driver usbhid
[ 3.297639] usbhid: USB HID core driver
[ 3.304000] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2:1.0/input/input4
[ 3.305035] hid-generic 0003:046D:C52F.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:12.0-2/input0
[ 3.308607] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:12.0/usb4/4-2/4-2:1.1/input/input5
[ 3.308971] hid-generic 0003:046D:C52F.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:12.0-2/input1
[ 5.282258] EXT4-fs (sda7): INFO: recovery required on readonly filesystem
[ 5.282270] EXT4-fs (sda7): write access will be enabled during recovery
[ 9.517439] EXT4-fs (sda7): recovery complete
[ 9.531955] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 12.515922] Adding 1814524k swap on /dev/sda6. Priority:-1 extents:1 across:1814524k
[ 13.762405] udevd[343]: starting version 175
[ 13.802501] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 14.699162] lp: driver loaded but no devices found
[ 16.106884] EXT4-fs (sda7): re-mounted. Opts: errors=remount-ro
[ 16.889596] acpi device:26: registered as cooling_device2
[ 16.889703] ACPI: Video Device [VGA1] (multi-head: yes rom: no post: no)
[ 16.890012] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input6
[ 16.957929] wmi: Mapper loaded
[ 17.338318] cfg80211: Calling CRDA to update world regulatory domain
[ 17.463917] microcode: CPU0: patch_level=0x0500010d
[ 17.537591] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \SMBX 1 (20120320/utaddress-251)
[ 17.537613] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 17.551315] asus_wmi: ASUS WMI generic driver loaded
[ 17.555382] asus_wmi: Initialization: 0x0asus_wmi: BIOS WMI version: 1.6
[ 17.555717] asus_wmi: SFUN value: 0x30<6>[ 17.558172] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input7
[ 17.582069] asus_wmi: Backlight controlled by ACPI video driver
[ 18.010240] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.4, id: 0x1e0b1, caps: 0xd04773/0xa40000/0xa0400
[ 18.046567] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
[ 18.175818] [drm] Initialized drm 1.1.0 20060810
[ 18.218399] sp5100_tco: SP5100 TCO WatchDog Timer Driver v0.01
[ 18.218607] sp5100_tco: mmio address 0xbafe00 already in use
[ 18.259341] microcode: CPU1: patch_level=0x0500010d
[ 18.268239] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 18.411659] Linux video capture interface: v2.00
[ 18.506572] snd_hda_intel 0000:00:01.1: irq 41 for MSI/MSI-X
[ 18.526569] kvm: Nested Virtualization enabled
[ 18.526587] kvm: Nested Paging enabled
[ 18.553404] input: HD-Audio Generic HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:01.1/sound/card0/input9
[ 18.683083] input: HDA ATI SB Mic as /devices/pci0000:00/0000:00:14.2/sound/card1/input10
[ 18.683358] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card1/input11
[ 18.688694] uvcvideo: Found UVC 1.00 device USB 2.0 UVC VGA WebCam (13d3:5716)
[ 18.693426] type=1400 audit(1383033403.948:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=753 comm="apparmor_parser"
[ 18.693479] type=1400 audit(1383033403.948:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=754 comm="apparmor_parser"
[ 18.694920] type=1400 audit(1383033403.948:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=753 comm="apparmor_parser"
[ 18.694995] type=1400 audit(1383033403.948:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=754 comm="apparmor_parser"
[ 18.695779] type=1400 audit(1383033403.948:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=753 comm="apparmor_parser"
[ 18.695891] type=1400 audit(1383033403.948:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=754 comm="apparmor_parser"
[ 18.708705] input: USB 2.0 UVC VGA WebCam as /devices/pci0000:00/0000:00:12.2/usb1/1-5/1-5:1.0/input/input12
[ 18.708999] usbcore: registered new interface driver uvcvideo
[ 18.709007] USB Video Class driver (1.1.1)
[ 18.727409] ath: EEPROM regdomain: 0x60
[ 18.727423] ath: EEPROM indicates we should expect a direct regpair map
[ 18.727434] ath: Country alpha2 being used: 00
[ 18.727439] ath: Regpair used: 0x60
[ 18.727993] cfg80211: Updating information on frequency 2412 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728042] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728050] cfg80211: Updating information on frequency 2417 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728057] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728063] cfg80211: Updating information on frequency 2422 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728070] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728075] cfg80211: Updating information on frequency 2427 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728082] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728088] cfg80211: Updating information on frequency 2432 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728095] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728101] cfg80211: Updating information on frequency 2437 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728107] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728113] cfg80211: Updating information on frequency 2442 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728120] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728126] cfg80211: Updating information on frequency 2447 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728132] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728138] cfg80211: Updating information on frequency 2452 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728145] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728151] cfg80211: Updating information on frequency 2457 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728157] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728163] cfg80211: Updating information on frequency 2462 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728170] cfg80211: 2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728176] cfg80211: Updating information on frequency 2467 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728182] cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728188] cfg80211: Updating information on frequency 2472 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728195] cfg80211: 2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.728201] cfg80211: Updating information on frequency 2484 MHz for a 20 MHz width channel with regulatory rule:
[ 18.728207] cfg80211: 2474000 KHz - 2494000 KHz @ 40000 KHz), (N/A mBi, 2000 mBm)
[ 18.733665] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 18.842819] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 18.846744] Registered led device: ath9k-phy0
[ 18.846780] ieee80211 phy0: Atheros AR9485 Rev:1 mem=0xffffc90010a00000, irq=17
[ 19.439494] [drm] radeon defaulting to kernel modesetting.
[ 19.439509] [drm] radeon kernel modesetting enabled.
[ 19.441645] [drm] initializing kernel modesetting (PALM 0x1002:0x9807 0x1043:0x103B).
[ 19.441744] [drm] register mmio base: 0xFEB00000
[ 19.441750] [drm] register mmio size: 262144
[ 19.441910] ATOM BIOS: AMD
[ 19.441988] radeon 0000:00:01.0: VRAM: 256M 0x0000000000000000 - 0x000000000FFFFFFF (256M used)
[ 19.441996] radeon 0000:00:01.0: GTT: 512M 0x0000000010000000 - 0x000000002FFFFFFF
[ 19.442321] [drm] Detected VRAM RAM=256M, BAR=256M
[ 19.442333] [drm] RAM width 32bits DDR
[ 19.442692] [TTM] Zone kernel: Available graphics memory: 887394 kiB
[ 19.442703] [TTM] Initializing pool allocator
[ 19.442729] [TTM] Initializing DMA pool allocator
[ 19.442812] [drm] radeon: 256M of VRAM memory ready
[ 19.442819] [drm] radeon: 512M of GTT memory ready.
[ 19.442874] [drm] GART: num cpu pages 131072, num gpu pages 131072
[ 19.450280] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain
[ 19.450295] cfg80211: World regulatory domain updated:
[ 19.450299] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 19.450305] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.450312] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.450318] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 19.450325] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.450331] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 19.458843] [drm] Loading PALM Microcode
[ 20.137233] [drm] PCIE GART of 512M enabled (table at 0x0000000000040000).
[ 20.137496] radeon 0000:00:01.0: WB enabled
[ 20.137511] radeon 0000:00:01.0: fence driver on ring 0 use gpu addr 0x0000000010000c00 and cpu addr 0xffff88006baa8c00
[ 20.137521] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 20.137526] [drm] Driver supports precise vblank timestamp query.
[ 20.137613] radeon 0000:00:01.0: irq 42 for MSI/MSI-X
[ 20.137678] radeon 0000:00:01.0: radeon: using MSI.
[ 20.137744] [drm] radeon: irq initialized.
[ 20.156216] [drm] ring test on 0 succeeded in 1 usecs
[ 20.156541] [drm] ib test on ring 0 succeeded in 0 usecs
[ 20.187065] init: failsafe main process (797) killed by TERM signal
[ 20.224062] [drm] radeon atom DIG backlight initialized
[ 20.224084] [drm] Radeon Display Connectors
[ 20.224091] [drm] Connector 0:
[ 20.224098] [drm] LVDS-1
[ 20.224103] [drm] HPD1
[ 20.224111] [drm] DDC: 0x6430 0x6430 0x6434 0x6434 0x6438 0x6438 0x643c 0x643c
[ 20.224114] [drm] Encoders:
[ 20.224118] [drm] LCD1: INTERNAL_UNIPHY
[ 20.224122] [drm] Connector 1:
[ 20.224126] [drm] HDMI-A-1
[ 20.224129] [drm] HPD2
[ 20.224134] [drm] DDC: 0x6440 0x6440 0x6444 0x6444 0x6448 0x6448 0x644c 0x644c
[ 20.224137] [drm] Encoders:
[ 20.224140] [drm] DFP1: INTERNAL_UNIPHY
[ 20.224144] [drm] Connector 2:
[ 20.224147] [drm] VGA-1
[ 20.224153] [drm] DDC: 0x64d8 0x64d8 0x64dc 0x64dc 0x64e0 0x64e0 0x64e4 0x64e4
[ 20.224156] [drm] Encoders:
[ 20.224159] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 20.224232] [drm] Internal thermal controller without fan control
[ 20.224522] [drm] radeon: power management initialized
[ 20.654665] [drm] fb mappable at 0xC0142000
[ 20.654675] [drm] vram apper at 0xC0000000
[ 20.654679] [drm] size 4325376
[ 20.654683] [drm] fb depth is 24
[ 20.654687] [drm] pitch is 5632
[ 20.655305] fbcon: radeondrmfb (fb0) is primary device
[ 20.655779] Console: switching to colour frame buffer device 170x48
[ 20.655850] fb0: radeondrmfb frame buffer device
[ 20.655854] drm: registered panic notifier
[ 20.655890] [drm] Initialized radeon 2.18.0 20080528 for 0000:00:01.0 on minor 0
[ 22.325371] ppdev: user-space parallel port driver
[ 22.357120] Bluetooth: Core ver 2.16
[ 22.357272] NET: Registered protocol family 31
[ 22.357280] Bluetooth: HCI device and connection manager initialized
[ 22.358508] Bluetooth: HCI socket layer initialized
[ 22.358522] Bluetooth: L2CAP socket layer initialized
[ 22.358545] Bluetooth: SCO socket layer initialized
[ 22.392827] Bluetooth: RFCOMM TTY layer initialized
[ 22.392844] Bluetooth: RFCOMM socket layer initialized
[ 22.392849] Bluetooth: RFCOMM ver 1.11
[ 22.457260] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 22.457270] Bluetooth: BNEP filters: protocol multicast
[ 23.071484] type=1400 audit(1383033408.324:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=923 comm="apparmor_parser"
[ 23.073306] type=1400 audit(1383033408.328:9): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=923 comm="apparmor_parser"
[ 23.450898] type=1400 audit(1383033408.704:10): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=951 comm="apparmor_parser"
[ 23.453246] type=1400 audit(1383033408.708:11): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=951 comm="apparmor_parser"
[ 23.746899] audit_printk_skb: 15 callbacks suppressed
[ 23.746910] type=1400 audit(1383033409.000:17): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=959 comm="apparmor_parser"
[ 24.358603] type=1400 audit(1383033409.612:18): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince" pid=953 comm="apparmor_parser"
[ 24.373029] type=1400 audit(1383033409.628:19): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince//sanitized_helper" pid=953 comm="apparmor_parser"
[ 24.375755] type=1400 audit(1383033409.628:20): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer" pid=953 comm="apparmor_parser"
[ 24.384559] type=1400 audit(1383033409.640:21): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-previewer//sanitized_helper" pid=953 comm="apparmor_parser"
[ 24.386600] type=1400 audit(1383033409.640:22): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer" pid=953 comm="apparmor_parser"
[ 24.392743] type=1400 audit(1383033409.648:23): apparmor="STATUS" operation="profile_load" name="/usr/bin/evince-thumbnailer//sanitized_helper" pid=953 comm="apparmor_parser"
[ 27.405772] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.406740] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 27.759434] r8169 0000:05:00.0: eth0: link down
[ 27.760666] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 27.761965] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 29.764120] cfg80211: Found new beacon on frequency: 2472 MHz (Ch 13) on phy0
[ 30.006632] wlan0: authenticate with 86:7d:ce:49:9a:6c
[ 30.013928] wlan0: send auth to 86:7d:ce:49:9a:6c (try 1/3)
[ 30.016073] wlan0: authenticated
[ 30.024565] wlan0: associate with 86:7d:ce:49:9a:6c (try 1/3)
[ 30.034125] wlan0: RX AssocResp from 86:7d:ce:49:9a:6c (capab=0x411 status=0 aid=1)
[ 30.034251] wlan0: associated
[ 30.034845] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
J'aime bien comprendre...

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

29 oct. 2013, 20:13

Mon ordi etait sur batterie et il a planté... (comme d'hab)

Ci dessous un copier collé de 2 fichiers log (sys.log et kernel.log) sur le temps de lantage:
sys.log

Oct 29 20:00:34 cisco-1225B kernel: [ 5557.400866] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.412367] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.412383] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.476811] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.592053] ath: phy0: Chip reset failed
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.592063] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.592172] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.603886] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.603904] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.666606] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.782036] ath: phy0: Chip reset failed
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.782046] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.782060] ath: phy0: Unable to set channel
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.793572] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.793589] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.856889] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.971886] ath: phy0: Chip reset failed
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.971896] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.971926] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.799695] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.799721] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.863399] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.977844] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.977855] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.977897] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.989564] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.989592] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.053018] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.168135] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.168146] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.168203] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.180095] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.180112] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.244279] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.359385] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.359395] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.359426] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.372502] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.372520] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.437347] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.552657] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.552666] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.552703] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.564446] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.564465] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.628142] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.743040] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.743049] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.743078] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.754603] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.754619] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.818895] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.933731] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.933741] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.933762] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.945472] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.945490] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.008596] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.123880] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.123889] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.123914] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.135387] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.135403] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.199542] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.314255] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.314265] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.314283] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.325853] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.325871] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.389743] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.505007] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.505017] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.505037] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.516571] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.516587] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.580274] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.695051] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.695060] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.695077] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.706525] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.706540] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.771007] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.886088] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.886097] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.886122] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.897824] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.897841] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.961474] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.076575] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.076584] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.076602] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.088059] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.088077] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.153197] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.268111] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.268120] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.268142] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.279874] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.279893] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.343686] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.458786] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.458796] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.458809] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.470350] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.470367] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.534172] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.648904] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.648913] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.648937] ath: phy0: Unable to set channel
Oct 29 20:04:42 cisco-1225B kernel: imklog 5.8.6, log source = /proc/kmsg started.
Oct 29 20:04:42 cisco-1225B rsyslogd: [origin software="rsyslogd" swVersion="5.8.6" x-pid="575" x-info="http://www.rsyslog.com"] start
Oct 29 20:04:42 cisco-1225B rsyslogd: rsyslogd's groupid changed to 103
Oct 29 20:04:42 cisco-1225B rsyslogd: rsyslogd's userid changed to 101
Oct 29 20:04:42 cisco-1225B rsyslogd-2039: Could not open output pipe '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ]
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Initializing cgroup subsys cpuset
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Initializing cgroup subsys cpu
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Linux version 3.5.0-42-generic (buildd@lamiak) (gcc version 4.7.2 (Ubuntu/Linaro 4.7.2-2ubuntu1) ) #65-Ubuntu SMP Tue Oct 1 23:38:22 UTC 2013 (Ubuntu 3.5.0-42.65-generic 3.5.7.21)
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-42-generic root=UUID=3bc10ab6-fa02-48a8-99b1-8372a3638af8 ro quiet splash i8042.reset i8042.nomux vt.handoff=7
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] KERNEL supported cpus:
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Intel GenuineIntel
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] AMD AuthenticAMD
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Centaur CentaurHauls
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] e820: BIOS-provided physical RAM map:
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006ec5dfff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ec5e000-0x000000006eca0fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006eca1000-0x000000006ecb2fff] ACPI data
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecb3000-0x000000006ecb5fff] ACPI NVS



KERN.LOG

ct 29 20:00:22 cisco-1225B kernel: [ 5544.826494] ath: phy0: Unable to set channel
Oct 29 20:00:22 cisco-1225B kernel: [ 5544.838159] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:22 cisco-1225B kernel: [ 5544.838176] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:22 cisco-1225B kernel: [ 5544.902137] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.017108] ath: phy0: Chip reset failed
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.017118] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.017138] ath: phy0: Unable to set channel
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.028590] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.028606] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.093385] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.208202] ath: phy0: Chip reset failed
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.208212] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.208224] ath: phy0: Unable to set channel
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.219854] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.219872] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.283782] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.398821] ath: phy0: Chip reset failed
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.398831] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.398857] ath: phy0: Unable to set channel
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.410327] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.410343] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.474236] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.588833] ath: phy0: Chip reset failed
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.588842] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.588855] ath: phy0: Unable to set channel
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.600452] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.600470] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:22 cisco-1225B kernel: [ 5545.664167] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.779271] ath: phy0: Chip reset failed
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.779281] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.779299] ath: phy0: Unable to set channel
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.790762] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.790778] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.855194] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.969886] ath: phy0: Chip reset failed
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.969895] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.969918] ath: phy0: Unable to set channel
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.981450] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:23 cisco-1225B kernel: [ 5545.981467] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:23 cisco-1225B kernel: [ 5546.045862] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:23 cisco-1225B kernel: [ 5546.160838] ath: phy0: Chip reset failed
Oct 29 20:00:23 cisco-1225B kernel: [ 5546.160847] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:23 cisco-1225B kernel: [ 5546.160869] ath: phy0: Unable to set channel
Oct 29 20:00:28 cisco-1225B kernel: [ 5550.984556] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:28 cisco-1225B kernel: [ 5550.984582] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.049286] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.163865] ath: phy0: Chip reset failed
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.163876] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.163969] ath: phy0: Unable to set channel
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.175783] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.175812] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.239434] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.354082] ath: phy0: Chip reset failed
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.354093] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.354144] ath: phy0: Unable to set channel
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.367258] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.367278] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.430783] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.545696] ath: phy0: Chip reset failed
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.545706] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.545740] ath: phy0: Unable to set channel
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.557501] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.557519] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.620273] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.735892] ath: phy0: Chip reset failed
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.735901] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:28 cisco-1225B kernel: [ 5551.735961] ath: phy0: Unable to set channel
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.747529] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.747546] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.813166] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.928132] ath: phy0: Chip reset failed
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.928141] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.928173] ath: phy0: Unable to set channel
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.929271] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.940249] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:29 cisco-1225B kernel: [ 5551.940270] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.003841] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.119472] ath: phy0: Chip reset failed
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.119481] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.119501] ath: phy0: Unable to set channel
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.131925] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.131945] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.194777] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.309879] ath: phy0: Chip reset failed
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.309888] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.309918] ath: phy0: Unable to set channel
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.321421] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.321438] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.384725] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.499995] ath: phy0: Chip reset failed
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.500033] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.500052] ath: phy0: Unable to set channel
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.514242] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.514271] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.577001] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.692328] ath: phy0: Chip reset failed
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.692337] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.692374] ath: phy0: Unable to set channel
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.704963] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:29 cisco-1225B kernel: [ 5552.704985] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.768705] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.883317] ath: phy0: Chip reset failed
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.883326] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.883353] ath: phy0: Unable to set channel
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.895071] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.895090] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:30 cisco-1225B kernel: [ 5552.959187] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.074850] ath: phy0: Chip reset failed
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.074860] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.074896] ath: phy0: Unable to set channel
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.088058] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.088076] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.151769] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.266304] ath: phy0: Chip reset failed
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.266313] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.266332] ath: phy0: Unable to set channel
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.277969] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.277987] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.343355] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.458788] ath: phy0: Chip reset failed
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.458797] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.458830] ath: phy0: Unable to set channel
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.470351] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.470367] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.534908] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.649855] ath: phy0: Chip reset failed
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.649864] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.649877] ath: phy0: Unable to set channel
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.661396] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.661414] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:30 cisco-1225B kernel: [ 5553.726683] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:31 cisco-1225B kernel: [ 5553.842060] ath: phy0: Chip reset failed
Oct 29 20:00:31 cisco-1225B kernel: [ 5553.842069] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:31 cisco-1225B kernel: [ 5553.842100] ath: phy0: Unable to set channel
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.111872] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.111899] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.175665] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.290137] ath: phy0: Chip reset failed
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.290148] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.290239] ath: phy0: Unable to set channel
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.301671] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.301688] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.366493] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.481795] ath: phy0: Chip reset failed
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.481805] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.481859] ath: phy0: Unable to set channel
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.493649] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.493668] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.558239] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.673512] ath: phy0: Chip reset failed
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.673521] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.673581] ath: phy0: Unable to set channel
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.685079] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.685096] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:32 cisco-1225B kernel: [ 5555.750185] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:33 cisco-1225B kernel: [ 5555.865321] ath: phy0: Chip reset failed
Oct 29 20:00:33 cisco-1225B kernel: [ 5555.865331] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:33 cisco-1225B kernel: [ 5555.865393] ath: phy0: Unable to set channel
Oct 29 20:00:33 cisco-1225B kernel: [ 5555.877088] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:33 cisco-1225B kernel: [ 5555.877107] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:33 cisco-1225B kernel: [ 5555.941849] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.057212] ath: phy0: Chip reset failed
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.057222] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.057276] ath: phy0: Unable to set channel
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.068774] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.068791] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.134353] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.249338] ath: phy0: Chip reset failed
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.249347] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.249390] ath: phy0: Unable to set channel
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.261112] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.261131] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.325941] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.441479] ath: phy0: Chip reset failed
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.441489] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.441599] ath: phy0: Unable to set channel
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.453077] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.453093] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.517395] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.632383] ath: phy0: Chip reset failed
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.632393] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.632473] ath: phy0: Unable to set channel
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.643999] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.644045] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:33 cisco-1225B kernel: [ 5556.709086] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:34 cisco-1225B kernel: [ 5556.824552] ath: phy0: Chip reset failed
Oct 29 20:00:34 cisco-1225B kernel: [ 5556.824561] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:34 cisco-1225B kernel: [ 5556.824640] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5556.836161] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5556.836178] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5556.901582] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.016634] ath: phy0: Chip reset failed
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.016643] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.016717] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.028172] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.028190] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.093764] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.209098] ath: phy0: Chip reset failed
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.209108] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.209156] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.220857] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.220874] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.285630] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.400816] ath: phy0: Chip reset failed
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.400825] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.400866] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.412367] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.412383] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.476811] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.592053] ath: phy0: Chip reset failed
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.592063] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.592172] ath: phy0: Unable to set channel
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.603886] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.603904] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:34 cisco-1225B kernel: [ 5557.666606] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.782036] ath: phy0: Chip reset failed
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.782046] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.782060] ath: phy0: Unable to set channel
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.793572] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.793589] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.856889] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.971886] ath: phy0: Chip reset failed
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.971896] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:35 cisco-1225B kernel: [ 5557.971926] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.799695] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.799721] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.863399] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.977844] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.977855] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.977897] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.989564] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5562.989592] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.053018] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.168135] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.168146] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.168203] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.180095] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.180112] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.244279] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.359385] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.359395] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.359426] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.372502] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.372520] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.437347] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.552657] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.552666] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.552703] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.564446] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.564465] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.628142] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.743040] ath: phy0: Chip reset failed
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.743049] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.743078] ath: phy0: Unable to set channel
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.754603] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:40 cisco-1225B kernel: [ 5563.754619] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.818895] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.933731] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.933741] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.933762] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.945472] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5563.945490] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.008596] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.123880] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.123889] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.123914] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.135387] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.135403] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.199542] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.314255] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.314265] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.314283] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.325853] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.325871] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.389743] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.505007] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.505017] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.505037] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.516571] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.516587] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.580274] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.695051] ath: phy0: Chip reset failed
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.695060] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.695077] ath: phy0: Unable to set channel
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.706525] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:41 cisco-1225B kernel: [ 5564.706540] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.771007] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.886088] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.886097] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.886122] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.897824] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.897841] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5564.961474] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.076575] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.076584] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.076602] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.088059] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.088077] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.153197] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.268111] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.268120] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.268142] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.279874] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.279893] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.343686] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.458786] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.458796] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.458809] ath: phy0: Unable to set channel
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.470350] ath: phy0: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff DMADBG_7=0xffffffff
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.470367] ath: phy0: Could not stop RX, we could be confusing the DMA engine when we start RX up
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.534172] ath: phy0: Failed to stop TX DMA, queues=0x10f!
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.648904] ath: phy0: Chip reset failed
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.648913] ath: phy0: Unable to reset channel, reset status -22
Oct 29 20:00:42 cisco-1225B kernel: [ 5565.648937] ath: phy0: Unable to set channel
Oct 29 20:04:42 cisco-1225B kernel: imklog 5.8.6, log source = /proc/kmsg started.
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Initializing cgroup subsys cpuset
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Initializing cgroup subsys cpu
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Linux version 3.5.0-42-generic (buildd@lamiak) (gcc version 4.7.2 (Ubuntu/Linaro 4.7.2-2ubuntu1) ) #65-Ubuntu SMP Tue Oct 1 23:38:22 UTC 2013 (Ubuntu 3.5.0-42.65-generic 3.5.7.21)
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-42-generic root=UUID=3bc10ab6-fa02-48a8-99b1-8372a3638af8 ro quiet splash i8042.reset i8042.nomux vt.handoff=7
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] KERNEL supported cpus:
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Intel GenuineIntel
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] AMD AuthenticAMD
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] Centaur CentaurHauls
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] e820: BIOS-provided physical RAM map:
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000006ec5dfff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ec5e000-0x000000006eca0fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006eca1000-0x000000006ecb2fff] ACPI data
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecb3000-0x000000006ecb5fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecb6000-0x000000006ecb8fff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecb9000-0x000000006ecc0fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecc1000-0x000000006ecdafff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecdb000-0x000000006ecdbfff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecdc000-0x000000006ecebfff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecec000-0x000000006ecf5fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ecf6000-0x000000006ed03fff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ed04000-0x000000006ed05fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ed06000-0x000000006ed07fff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ed08000-0x000000006ed0ffff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ed10000-0x000000006ed44fff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ed45000-0x000000006ed87fff] ACPI NVS
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x000000006ed88000-0x000000006eefffff] usable
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
Oct 29 20:04:42 cisco-1225B kernel: [ 0.000000] BIOS-e820: [mem 0x00000000fec10000-0x00000000fec10fff] reserved

Esperant que quel qu un pourra m aider avec ca...
Merci
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

29 oct. 2013, 23:18

Apparemment le problème a l'air de venir du wifi (ath). Pourrais tu nous faire un lspci dans un terminal.
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

30 oct. 2013, 08:28

Voila Pingux:
Merci pour ta patience..

00:00.0 Host bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Complex
00:01.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Wrestler [Radeon HD 6290]
00:01.1 Audio device: Advanced Micro Devices [AMD] nee ATI Wrestler HDMI Audio [Radeon HD 6250/6310]
00:04.0 PCI bridge: Advanced Micro Devices [AMD] Family 14h Processor Root Port
00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] (rev 40)
00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42)
00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40)
00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40)
00:14.5 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI2 Controller
00:15.0 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB700/SB800/SB900 PCI to PCI bridge (PCIE port 0)
00:15.1 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB700/SB800/SB900 PCI to PCI bridge (PCIE port 1)
00:15.3 PCI bridge: Advanced Micro Devices [AMD] nee ATI SB900 PCI to PCI bridge (PCIE port 3)
00:16.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:16.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 0 (rev 43)
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 1
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 2
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 3
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 4
00:18.5 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 6
00:18.6 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 5
00:18.7 Host bridge: Advanced Micro Devices [AMD] Family 12h/14h Processor Function 7
04:00.0 Network controller: Atheros Communications Inc. AR9485 Wireless Network Adapter (rev 01)
05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

30 oct. 2013, 09:37

Pourrais tu nous en dire un peu plus sur les plantages, à quel moment il arrivent, et ton wifi est ce qu'il fonctionne normalement (fiabilité, vitesse...)
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

30 oct. 2013, 10:33

Le WIFI fonctionne tres bien, il n y a jamais de coupure.
Ce que je vois lors du plantage, c'est que souvent le WIFI est en train de se reconecter (d ou le fait que je pense que ça vient de la)
Les plantages arrivent soit au bout de 2 min...soit au bout de 40min...c'est aléatoire..

Je met un lien sur un forum ou la personne a eu un meme probleme, elle me conseille le noyeau 3.8:
http://forum.ubuntu-fr.org/viewtopic.ph ... #p15053871

C'est vrai que je souhaiterai comprendre le probleme avant de rectifier..

Qu en penses tu?

MErci encore
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

30 oct. 2013, 18:40

Tu es sur une 12.10, tu peux mettre à niveau vers la 13.10 dont le noyau est 3.8.0-26. Mais vu les problèmes de plantages je conseillerai une nouvelle installation.
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

31 oct. 2013, 10:07

J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

31 oct. 2013, 12:29

Le mieux serait je crois de faire une sauvegarde de tes données et de faire une installation neuve avec une 13.10 qui a le noyau qu'il faut pour ta machine.
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

03 nov. 2013, 10:00

13.10 installée mais clavier ne fonctionne pas.... Y a t il une commande a faire?
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

03 nov. 2013, 10:20

Via le "Gestionnaire de paramètres" la section "Matériel" et l'Icône clavier.
Dura Lex sed Lex

CISCO
Messages : 15
Enregistré le : 06 avr. 2013, 16:29
Contact : Envoyer un message privé

Re: ca plante sur batterie

03 nov. 2013, 10:28

Il est configuré mais ne répond pas...
De plus, ça Freese encore sur batterie..... :cry:
J'aime bien comprendre...

pingux
Messages : 2508
Enregistré le : 28 déc. 2011, 17:19
Localisation : Belgique
Contact : Envoyer un message privé

Re: ca plante sur batterie

03 nov. 2013, 20:55

Pour débloquer le clavier et le pavé tactile, j'ai trouvé cette solution. Il faut éditer le fichier /etc/default/grub et remplacer la ligne
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash" par
GRUB_CMDLINE_LINUX_DEFAULT="quiet splash i8042.reset i8042.nomux"

Le tout suivi d'un sudo update-grub

Encore faut-il que tu puisses te servir de ton clavier, pour cela essaie quelques démarrage successifs jusqu'à ce que cela marche.
D'après ce que j'ai vu sur différents forums, cette machine est un vrais nid à problèmes sous Linux.
Dura Lex sed Lex

Retourner vers « Xubuntu »